Add the nodes for CMB subunit MSR(mux select register) support.
CMB MSRs(mux select registers) is to separate mux,arbitration,
,interleaving,data packing control from stream filtering control.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>

Add property "qcom,cmb_msr_num" to support CMB MSR(mux select register)
for TPDM. It specifies the number of CMB MSR registers supported by
the TDPM.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>

CMB_TIER register is CMB subunit timestamp insertion enable register.
Bit 0 is PATT_TSENAB bit. Set this bit to 1 to request a timestamp
following a CMB interface pattern match. Bit 1 is XTRIG_TSENAB bit.
Set this bit to 1 to request a timestamp following a CMB CTI timestamp
request. Bit 2 is TS_ALL bit. Set this bit to 1 to request timestamp
for all packets.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Jinlong Mao <quic_jinlmao@quicinc.com>

Timestamps are requested if the monitor’s CMB data set unit input
data matches the value in the Monitor CMB timestamp pattern and mask
registers (M_CMB_TPR and M_CMB_TPMR) when CMB timestamp enabled
via the timestamp insertion enable register bit(CMB_TIER.PATT_TSENAB).
The pattern match trigger output is achieved via setting values into
the CMB trigger pattern and mask registers (CMB_XPR and CMB_XPMR).
After configuring a pattern through these registers, the TPDM subunit
will assert an output trigger every time it receives new input data
that matches the configured pattern value. Values in a given bit
number of the mask register correspond to the same bit number in
the corresponding pattern register.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Jinlong Mao <quic_jinlmao@quicinc.com>

TPDM CMB subunits support two forms of CMB data set element creation:
continuous and trace-on-change collection mode. Continuous change
creates CMB data set elements on every CMBCLK edge. Trace-on-change
creates CMB data set elements only when a new data set element differs
in value from the previous element in a CMB data set. Set CMB_CR.MODE
to 0 for continuous CMB collection mode. Set CMB_CR.MODE to 1 for
trace-on-change CMB collection mode

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Jinlong Mao <quic_jinlmao@quicinc.com>

CMB (continuous multi-bit) is one of TPDM's dataset type. CMB subunit
can be enabled for data collection by writing 1 to the first bit of
CMB_CR register. This change is to add enable/disable function for
CMB dataset by writing CMB_CR register.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Jinlong Mao <quic_jinlmao@quicinc.com>

Read the CMB element size from the device tree. Set the register
bit that controls the CMB element size of the corresponding port.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>

Add property "qcom,cmb-elem-size" to support CMB(Continuous
Multi-Bit) element for TPDM. The associated aggregator will read
this size before it is enabled. CMB element size currently only
supports 32-bit and 64-bit.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com>

Correct the property name of the DSB MSR number that needs to be
read in TPDM driver. The right property name is
"qcom,dsb-msrs-num".

Fixes： 90a7371c ("coresight-tpdm: Add nodes for dsb msr support")
Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

Add the nodes for DSB subunit MSR(mux select register) support.
The TPDM MSR (mux select register) interface is an optional
interface and associated bank of registers per TPDM subunit.
The intent of mux select registers is to control muxing structures
driving the TPDM’s’ various subunit interfaces.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

Add property "qcom,dsb-msrs-num" to support DSB(Discrete Single
Bit) MSR(mux select register) for TPDM. It specifies the number
of MSR registers supported by the DSB TDPM.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>

Add nodes to configure the timestamp request based on input
pattern match. Each TPDM that support DSB subunit has maximum of
n(n<7) TPR registers to configure value for timestamp request
based on input pattern match. Eight 32 bit registers providing
DSB interface timestamp request  pattern match comparison. And
each TPDM that support DSB subunit has maximum of m(m<7) TPMR
registers to configure pattern mask for timestamp request. Eight
32 bit registers providing DSB interface timestamp request
pattern match mask generation. Add nodes to enable/disable
pattern timestamp and set pattern timestamp type.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

Add nodes to configure trigger pattern and trigger pattern mask.
Each DSB subunit TPDM has maximum of n(n<7) XPR registers to
configure trigger pattern match output. Eight 32 bit registers
providing DSB interface trigger output pattern match comparison.
And each DSB subunit TPDM has maximum of m(m<7) XPMR registers to
configure trigger pattern mask match output. Eight 32 bit
registers providing DSB interface trigger output pattern match
mask.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

Add the nodes to set value for DSB edge control and DSB edge
control mask. Each DSB subunit TPDM has maximum of n(n<16) EDCR
resgisters to configure edge control. DSB edge detection control
00: Rising edge detection
01: Falling edge detection
10: Rising and falling edge detection (toggle detection)
And each DSB subunit TPDM has maximum of m(m<8) ECDMR registers to
configure mask. Eight 32 bit registers providing DSB interface
edge detection mask control.

Add the nodes to configure DSB edge control and DSB edge control
mask. Each DSB subunit TPDM maximum of 256 edge detections can be
configured. The index and value sysfs files need to be paired and
written to order. The index sysfs file is to set the index number
of the edge detection which needs to be configured. And the value
sysfs file is to set the control or mask for the edge detection.
DSB edge detection control should be set as the following values.
00: Rising edge detection
01: Falling edge detection
10: Rising and falling edge detection (toggle detection)
And DSB edge mask should be set as 0 or 1.
Each DSB subunit TPDM has maximum of n(n<16) EDCR resgisters to
configure edge control. And each DSB subunit TPDM has maximum of
m(m<8) ECDMR registers to configure mask.

Add the nodes to read a set of the edge control value and mask
of the DSB in TPDM.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

Add node to set and show programming mode for TPDM DSB subunit.
Once the DSB programming mode is set, it will be written to the
register DSB_CR.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

The nodes are needed to set or show the trigger timestamp and
trigger type. This change is to add these nodes to achieve these
function.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

TPDM device need a node to reset the configurations and status of
it. This change provides a node to reset the configurations and
disable the TPDM if it has been enabled.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

DSB is used for monitoring “events”. Events are something that
occurs at some point in time. It could be a state decode, the
act of writing/reading a particular address, a FIFO being empty,
etc. This decoding of the event desired is done outside TPDM.
DSB subunit need to be configured in enablement and disablement.
A struct that specifics associated to dsb dataset is needed. It
saves the configuration and parameters of the dsb datasets. This
change is to add this struct and initialize the configuration of
DSB subunit.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

Read the DSB element size from the device tree. Set the register
bit that controls the DSB element size of the corresponding port.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

Introduce the new subtype of "CORESIGHT_DEV_SUBTYPE_SOURCE_TPDM"
for TPDM components in driver.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

Add property "qcom,dsb-elem-size" to support DSB(Discrete Single
Bit) element for TPDM. The associated aggregator will read this
size before it is enabled. DSB element size currently only
supports 32-bit and 64-bit.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>
Acked-by: Rob Herring <robh@kernel.org>

Remove the unnecessary lock "CS_{UN,}LOCK" in TPDM driver. This
lock is only needed while writing the data to Coresight registers.

Signed-off-by: Tao Zhang <quic_taozha@quicinc.com>

Pull SCSI fixes from James Bottomley:
 "A single fix for libata: older devices don't support command duration
  limits (CDL) and some don't support report opcodes, meaning there's no
  way to tell if they support the command or not.

  Reduce the problems of incorrectly using CDL commands on older devices
  by checking SCSI spec compliance at SPC-5 (the spec which introduced
  the command) before turning on CDL"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: core: ata: Do no try to probe for CDL on old drives

Pull VFIO fixes from Alex Williamson:

 - The new PDS vfio-pci variant driver only supports SR-IOV VF devices
   and incorrectly made a direct reference to the physfn field of the
   pci_dev.  Fix this both by making the Kconfig depend on IOV support
   as well as using the correct wrapper for this access (Shixiong Ou)

 - Resolve an error path issue where on unwind of the mdev registration
   the created kset is not unregistered and the wrong error code is
   returned (Jinjie Ruan)

* tag 'vfio-v6.6-rc4' of https://github.com/awilliam/linux-vfio:
  vfio/mdev: Fix a null-ptr-deref bug for mdev_unregister_parent()
  vfio/pds: Use proper PF device access helper
  vfio/pds: Add missing PCI_IOV depends

Pull workqueue fixes from Tejun Heo:

 - Remove double allocation of wq_update_pod_attrs_buf

 - Fix missing allocation of pwq_release_worker when
   wq_cpu_intensive_thresh_us is set to a custom value

* tag 'wq-for-6.6-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: Fix missed pwq_release_worker creation in wq_cpu_intensive_thresh_init()
  workqueue: Removed double allocation of wq_update_pod_attrs_buf

Pull btrfs fixes from David Sterba:

 - delayed refs fixes:
     - fix race when refilling delayed refs block reserve
     - prevent transaction block reserve underflow when starting
       transaction
     - error message and value adjustments

 - fix build warnings with CONFIG_CC_OPTIMIZE_FOR_SIZE and
   -Wmaybe-uninitialized

 - fix for smatch report where uninitialized data from invalid extent
   buffer range could be returned to the caller

 - fix numeric overflow in statfs when calculating lower threshold
   for a full filesystem

* tag 'for-6.6-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: initialize start_slot in btrfs_log_prealloc_extents
  btrfs: make sure to initialize start and len in find_free_dev_extent
  btrfs: reset destination buffer when read_extent_buffer() gets invalid range
  btrfs: properly report 0 avail for very full file systems
  btrfs: log message if extent item not found when running delayed extent op
  btrfs: remove redundant BUG_ON() from __btrfs_inc_extent_ref()
  btrfs: return -EUCLEAN for delayed tree ref with a ref count not equals to 1
  btrfs: prevent transaction block reserve underflow when starting transaction
  btrfs: fix race when refilling delayed refs block reserve

Merge tag 'linux-kselftest-fixes-6.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull kselftest fix from Shuah Khan:
 "One single fix to unmount tracefs when test created mount"

* tag 'linux-kselftest-fixes-6.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/user_events: Fix to unmount tracefs when test created mount

Pull vfs fixes from Christian Brauner:
 "This contains the usual miscellaneous fixes and cleanups for vfs and
  individual fses:

  Fixes:
   - Revert ki_pos on error from buffered writes for direct io fallback
   - Add missing documentation for block device and superblock handling
     for changes merged this cycle
   - Fix reiserfs flexible array usage
   - Ensure that overlayfs sets ctime when setting mtime and atime
   - Disable deferred caller completions with overlayfs writes until
     proper support exists

  Cleanups:
   - Remove duplicate initialization in pipe code
   - Annotate aio kioctx_table with __counted_by"

* tag 'v6.6-rc4.vfs.fixes' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs:
  overlayfs: set ctime when setting mtime and atime
  ntfs3: put resources during ntfs_fill_super()
  ovl: disable IOCB_DIO_CALLER_COMP
  porting: document superblock as block device holder
  porting: document new block device opening order
  fs/pipe: remove duplicate "offset" initializer
  fs-writeback: do not requeue a clean inode having skipped pages
  aio: Annotate struct kioctx_table with __counted_by
  direct_write_fallback(): on error revert the ->ki_pos update from buffered write
  reiserfs: Replace 1-element array with C99 style flex-array

Merge tag 'perf-tools-fixes-for-v6.6-1-2023-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools

Pull perf tools fixes from Namhyung Kim:
 "Build:

   - Update header files in the tools/**/include directory to sync with
     the kernel sources as usual.

   - Remove unused bpf-prologue files. While it's not strictly a fix,
     but the functionality was removed in this cycle so better to get
     rid of the code together.

   - Other minor build fixes.

  Misc:

   - Fix uninitialized memory access in PMU parsing code

   - Fix segfaults on software event"

* tag 'perf-tools-fixes-for-v6.6-1-2023-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
  perf jevent: fix core dump on software events on s390
  perf pmu: Ensure all alias variables are initialized
  perf jevents metric: Fix type of strcmp_cpuid_str
  perf trace: Avoid compile error wrt redefining bool
  perf bpf-prologue: Remove unused file
  tools headers UAPI: Update tools's copy of drm.h headers
  tools arch x86: Sync the msr-index.h copy with the kernel sources
  perf bench sched-seccomp-notify: Use the tools copy of seccomp.h UAPI
  tools headers UAPI: Copy seccomp.h to be able to build 'perf bench' in older systems
  tools headers UAPI: Sync files changed by new fchmodat2 and map_shadow_stack syscalls with the kernel sources
  perf tools: Update copy of libbpf's hashmap.c

Nathan reported that he was seeing the new warning in
setattr_copy_mgtime pop when starting podman containers. Overlayfs is
trying to set the atime and mtime via notify_change without also
setting the ctime.

POSIX states that when the atime and mtime are updated via utimes() that
we must also update the ctime to the current time. The situation with
overlayfs copy-up is analogies, so add ATTR_CTIME to the bitmask.
notify_change will fill in the value.

Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Christian Brauner <brauner@kernel.org>
Acked-by: Amir Goldstein <amir73il@gmail.com>
Message-Id: <20230913-ctime-v1-1-c6bc509cbc27@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>

During ntfs_fill_super() some resources are allocated that we need to
cleanup in ->put_super() such as additional inodes. When
ntfs_fill_super() fails these resources need to be cleaned up as well.

Reported-by:  <syzbot+2751da923b5eb8307b0b@syzkaller.appspotmail.com>
Fixes: 78a06688 ("ntfs3: drop inode references in ntfs_put_super()")
Signed-off-by: Christian Brauner <brauner@kernel.org>

overlayfs copies the kiocb flags when it sets up a new kiocb to handle
a write, but it doesn't properly support dealing with the deferred
caller completions of the kiocb. This means it doesn't get the final
write completion value, and hence will complete the write with '0' as
the result.

We could support the caller completions in overlayfs, but for now let's
just disable them in the generated write kiocb.

Reported-by: Zorro Lang <zlang@redhat.com>
Link: https://lore.kernel.org/io-uring/20230924142754.ejwsjen5pvyc32l4@dell-per750-06-vm-08.rhts.eng.pek2.redhat.com/


Fixes: 8c052fb3 ("iomap: support IOCB_DIO_CALLER_COMP")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Message-Id: <71897125-e570-46ce-946a-d4729725e28f@kernel.dk>
Signed-off-by: Christian Brauner <brauner@kernel.org>

Pull kvm fixes from Paolo Bonzini:
"ARM:

   - Fix EL2 Stage-1 MMIO mappings where a random address was used

   - Fix SMCCC function number comparison when the SVE hint is set

  RISC-V:

   - Fix KVM_GET_REG_LIST API for ISA_EXT registers

   - Fix reading ISA_EXT register of a missing extension

   - Fix ISA_EXT register handling in get-reg-list test

   - Fix filtering of AIA registers in get-reg-list test

  x86:

   - Fixes for TSC_AUX virtualization

   - Stop zapping page tables asynchronously, since we don't zap them as
     often as before"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: SVM: Do not use user return MSR support for virtualized TSC_AUX
  KVM: SVM: Fix TSC_AUX virtualization setup
  KVM: SVM: INTERCEPT_RDTSCP is never intercepted anyway
  KVM: x86/mmu: Stop zapping invalidated TDP MMU roots asynchronously
  KVM: x86/mmu: Do not filter address spaces in for_each_tdp_mmu_root_yield_safe()
  KVM: x86/mmu: Open code leaf invalidation from mmu_notifier
  KVM: riscv: selftests: Selectively filter-out AIA registers
  KVM: riscv: selftests: Fix ISA_EXT register handling in get-reg-list
  RISC-V: KVM: Fix riscv_vcpu_get_isa_ext_single() for missing extensions
  RISC-V: KVM: Fix KVM_GET_REG_LIST API for ISA_EXT registers
  KVM: selftests: Assert that vasprintf() is successful
  KVM: arm64: nvhe: Ignore SVE hint in SMCCC function ID
  KVM: arm64: Properly return allocated EL2 VA from hyp_alloc_private_va_range()

Pull tracing fixes from Steven Rostedt:

 - Fix the "bytes" output of the per_cpu stat file

   The tracefs/per_cpu/cpu*/stats "bytes" was giving bogus values as the
   accounting was not accurate. It is suppose to show how many used
   bytes are still in the ring buffer, but even when the ring buffer was
   empty it would still show there were bytes used.

 - Fix a bug in eventfs where reading a dynamic event directory (open)
   and then creating a dynamic event that goes into that diretory screws
   up the accounting.

   On close, the newly created event dentry will get a "dput" without
   ever having a "dget" done for it. The fix is to allocate an array on
   dir open to save what dentries were actually "dget" on, and what ones
   to "dput" on close.

* tag 'trace-v6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  eventfs: Remember what dentries were created on dir open
  ring-buffer: Fix bytes info in per_cpu buffer stats

Pull cxl fixes from Dan Williams:
 "A collection of regression fixes, bug fixes, and some small cleanups
  to the Compute Express Link code.

  The regressions arrived in the v6.5 dev cycle and missed the v6.6
  merge window due to my personal absences this cycle. The most
  important fixes are for scenarios where the CXL subsystem fails to
  parse valid region configurations established by platform firmware.
  This is important because agreement between OS and BIOS on the CXL
  configuration is fundamental to implementing "OS native" error
  handling, i.e. address translation and component failure
  identification.

  Other important fixes are a driver load error when the BIOS lets the
  Linux PCI core handle AER events, but not CXL memory errors.

  The other fixex might have end user impact, but for now are only known
  to trigger in our test/emulation environment.

  Summary:

   - Fix multiple scenarios where platform firmware defined regions fail
     to be assembled by the CXL core.

   - Fix a spurious driver-load failure on platforms that enable OS
     native AER, but not OS native CXL error handling.

   - Fix a regression detecting "poison" commands when "security"
     commands are also defined.

   - Fix a cxl_test regression with the move to centralize CXL port
     register enumeration in the CXL core.

   - Miscellaneous small fixes and cleanups"

* tag 'cxl-fixes-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
  cxl/acpi: Annotate struct cxl_cxims_data with __counted_by
  cxl/port: Fix cxl_test register enumeration regression
  cxl/region: Refactor granularity select in cxl_port_setup_targets()
  cxl/region: Match auto-discovered region decoders by HPA range
  cxl/mbox: Fix CEL logic for poison and security commands
  cxl/pci: Replace host_bridge->native_aer with pcie_aer_is_native()
  PCI/AER: Export pcie_aer_is_native()
  cxl/pci: Fix appropriate checking for _OSC while handling CXL RAS registers

Pull gpio fixes from Bartosz Golaszewski:

 - fix an invalid usage of __free(kfree) leading to kfreeing an
   ERR_PTR()

 - fix an irq domain leak in gpio-tb10x

 - MAINTAINERS update

* tag 'gpio-fixes-for-v6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpio: sim: fix an invalid __free() usage
  gpio: tb10x: Fix an error handling path in tb10x_gpio_probe()
  MAINTAINERS: gpio-regmap: make myself a maintainer of it

Merge tag 'mm-hotfixes-stable-2023-09-23-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm

Pull misc fixes from Andrew Morton:
 "13 hotfixes, 10 of which pertain to post-6.5 issues. The other three
  are cc:stable"

* tag 'mm-hotfixes-stable-2023-09-23-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  proc: nommu: fix empty /proc/<pid>/maps
  filemap: add filemap_map_order0_folio() to handle order0 folio
  proc: nommu: /proc/<pid>/maps: release mmap read lock
  mm: memcontrol: fix GFP_NOFS recursion in memory.high enforcement
  pidfd: prevent a kernel-doc warning
  argv_split: fix kernel-doc warnings
  scatterlist: add missing function params to kernel-doc
  selftests/proc: fixup proc-empty-vm test after KSM changes
  revert "scripts/gdb/symbols: add specific ko module load command"
  selftests: link libasan statically for tests with -fsanitize=address
  task_work: add kerneldoc annotation for 'data' argument
  mm: page_alloc: fix CMA and HIGHATOMIC landing on the wrong buddy list
  sh: mm: re-add lost __ref to ioremap_prot() to fix modpost warning

Pull smb client fixes from Steve French:
 "Six smb3 client fixes, including three for stable, from the SMB
  plugfest (testing event) this week:

   - Reparse point handling fix (found when investigating dir
     enumeration when fifo in dir)

   - Fix excessive thread creation for dir lease cleanup

   - UAF fix in negotiate path

   - remove duplicate error message mapping and fix confusing warning
     message

   - add dynamic trace point to improve debugging RDMA connection
     attempts"

* tag '6.6-rc2-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: fix confusing debug message
  smb: client: handle STATUS_IO_REPARSE_TAG_NOT_HANDLED
  smb3: remove duplicate error mapping
  cifs: Fix UAF in cifs_demultiplex_thread()
  smb3: do not start laundromat thread when dir leases  disabled
  smb3: Add dynamic trace points for RDMA (smbdirect) reconnect

Pull i2c fixes from Wolfram Sang:
 "A set of I2C driver fixes. Mostly fixing resource leaks or sanity
  checks"

* tag 'i2c-for-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: xiic: Correct return value check for xiic_reinit()
  i2c: mux: gpio: Add missing fwnode_handle_put()
  i2c: mux: demux-pinctrl: check the return value of devm_kstrdup()
  i2c: designware: fix __i2c_dw_disable() in case master is holding SCL low
  i2c: i801: unregister tco_pdev in i801_probe() error path